Scottsdale Epoxy Floors | Durable Epoxy Flooring in Scottsdale, AZ
Scottsdale Epoxy Floors installs epoxy and polyaspartic coatings for garages, patios, workshops, and commercial spaces throughout Scottsdale and the surrounding Phoenix metro area. We handle the full process, from diamond grinding and crack repair through final topcoat, so the finished surface bonds properly and holds up to daily use.
Arizona conditions are hard on concrete. Hot tire pickup, UV exposure on patios, and fine desert dust all shorten the life of a coating that was applied over unprepared concrete. Our preparation methods and material selection account for those factors.
On this page, you'll find our service offerings, the coating systems we install, the areas we serve, and how to request a quote. If you're comparing contractors, we've also outlined what separates a properly installed floor from one that peels within a year.
Request a FREE Quote.
Get the numbers you need to plan with confidence—no pressure, just clear and honest pricing.
Garage, Residential & Decorative Epoxy Flooring
We install coating systems that stand up to Scottsdale's summer heat, hot tire pickup, and the fine dust that finds its way into every garage. Every project starts with diamond grinding, moves through crack and spall repair, and finishes with the system that matches how you actually use the space.
Epoxy Garage Flooring
A garage floor coating is only as strong as the concrete prep underneath it. We mechanically grind the slab with diamond tooling to open the pores, then fill cracks and pitting with a rapid-set polyurea patch before any coating goes down. Our standard garage build uses a 100% solids epoxy base coat over prepped concrete, followed by a UV-stable topcoat.
The result resists hot tire pickup, motor oil, brake fluid, road salt, and dropped tools. Cleanup is a broom and a mop instead of a degreaser and a wire brush. Typical residential garages run 400 to 900 square feet and are completed in one to two days.
Residential Epoxy Flooring
Epoxy and polyaspartic work well beyond the garage. We coat patios, pool decks, casitas, laundry rooms, workshops, and interior concrete throughout Scottsdale, Paradise Valley, and North Scottsdale.
Outdoor applications get UV-stable topcoats and textured additives so surfaces stay comfortable and safe around water. Because these coatings are seamless, there are no grout lines to scrub and no seams for moisture to sit in. That makes them practical for homes with pets, and for spaces where dust and pollen are ongoing issues. We handle furniture moving, protect adjacent surfaces, and clean the site before we leave.
Polyaspartic Floor Coatings
Polyaspartic is a polyurea-based coating that cures far faster than standard epoxy and holds its color under direct UV exposure. That matters in Scottsdale, where a west-facing garage door can push interior slab temperatures well past what a straight epoxy topcoat handles comfortably.
Key differences we walk clients through:
Feature | Epoxy | Polyaspartic
|
|---|---|---|
Cure to foot traffic | 12–24 hours | 2–4 hours |
UV stability | Can amber over time | Holds color |
Application temperature range | Narrower | Wider |
Abrasion resistance | Strong | Higher |
We often use a hybrid build: an epoxy base coat for adhesion and thickness, topped with polyaspartic for scratch resistance and color retention. Many of these floors are ready to drive on within 24 hours.
Flake Epoxy Flooring
Flake systems, also called color chip or broadcast systems, use vinyl chips scattered into a wet base coat and then locked in with a clear topcoat. The texture hides slab imperfections, hairline cracks, and everyday dirt far better than a solid color.
Chips come in 1/8", 1/4", and 1" sizes, and we blend custom colors to coordinate with stucco, cabinetry, or brand palettes.
The broadcast level determines the look:
- Partial broadcast — some base color shows through, lighter texture
- Full broadcast (double broadcast) — chips completely cover the base, heavier texture, more slip resistance
Full flake systems typically finish around 20 to 30 mils thick. They are our most requested option for garages, laundry rooms, and patios.
Metallic Epoxy Flooring
Metallic epoxy uses reflective pigments suspended in a clear resin, manipulated with rollers, brushes, and solvent to create depth and movement. No two floors come out identical, which is part of the appeal for showrooms, home bars, retail spaces, and finished basements.
Common effects include marbled veining, cloud patterns, and lava-style pours.
These floors are seamless and easy to clean, but they show scratches more readily than flake systems and offer less slip resistance when wet. We address that with a polyaspartic clear coat and, where needed, an anti-slip additive.
Metallic installs take longer than standard systems because the design layer needs full cure before the topcoat goes on.
Commercial & Industrial Epoxy Floor Coatings
Businesses across Scottsdale need floors that hold up to forklifts, customer traffic, cleaning chemicals, and Arizona heat without cracking or peeling. We install epoxy and polyaspartic systems sized to the demands of each space, from a 1,200 square foot retail showroom to a 40,000 square foot warehouse.
Commercial Epoxy Flooring
Retail stores, restaurants, auto shops, medical offices, and gyms all place different demands on a floor. We match the system to the use.
For food service and healthcare, we recommend seamless epoxy with integral cove base, which eliminates the grout lines and floor-to-wall joints where bacteria collect. Showrooms and lobbies typically get metallic epoxy or a full-broadcast flake system with a polyaspartic topcoat for scuff resistance.
Most commercial work happens on nights and weekends. Polyaspartic topcoats cure in 2 to 4 hours, so a shop that closes Friday evening can often reopen Monday morning.
Common commercial applications:
- Restaurant kitchens and prep areas
- Auto dealerships and service bays
- Retail sales floors and stockrooms
- Veterinary clinics and medical facilities
- Breweries and commercial kitchens
Industrial Epoxy Flooring
Warehouses, manufacturing plants, and aircraft hangars require thicker builds than a standard garage coating. We install systems ranging from 20 mils up to 1/4-inch mortar for areas taking impact from dropped tooling or steel-wheeled equipment.
Chemical exposure drives material selection. Novolac epoxy resists sulfuric acid, solvents, and hydraulic fluid far better than standard epoxy, which makes it the right choice for battery charging stations and processing areas.
Requirement | System We Use
|
|---|---|
Heavy forklift traffic
| Epoxy mortar, 1/8" to 1/4" |
Chemical resistance
| Novolac epoxy |
Wet or greasy areas
| Broadcast aggregate, slip-resistant |
Static-sensitive work
| ESD conductive epoxy |
We also stripe walkways, forklift lanes, and safety zones in OSHA-referenced colors as part of the installation.
Concrete Floor Coatings
Not every project calls for a full epoxy build. Grind and seal, polished concrete, and urethane cement each solve specific problems at different price points.
Grind and seal exposes the existing slab and locks it under a densifier and sealer. It costs less than epoxy and works well for warehouse aisles and back-of-house areas where appearance matters less than dust control.
Urethane cement handles thermal shock, which matters in freezer rooms and kitchens with steam cleaning cycles. It tolerates temperature swings that would delaminate a standard epoxy.
Every system starts the same way: diamond grinding to open the concrete profile, moisture testing per ASTM F2170, and crack and joint repair before any coating goes down.
Outdoor Concrete & Deck Coatings
Scottsdale patios and pool decks face UV exposure above 300 sunny days a year, surface temperatures that can exceed 150°F, and monsoon moisture that pushes through untreated concrete. We install UV-stable polyaspartic and polyurea systems outdoors, with textured finishes that stay walkable when wet and cool enough for bare feet.
Patio Deck Coatings
Uncoated patio concrete in the Valley tends to fade, spall at the edges, and stain from planters, grills, and hard water runoff.
We start with diamond grinding to open the concrete profile, then repair cracks and spalled sections before any coating goes down. Skipping that prep is the most common reason outdoor coatings peel.
Our standard outdoor build is a moisture-tolerant base coat, broadcast flake for texture and color, and a UV-stable polyaspartic topcoat.
What that gives you:
- No yellowing — polyaspartic topcoats resist UV degradation, unlike straight epoxy
- Slip texture — flake broadcast plus an optional non-skid additive
- Stain resistance — sealed surface handles spilled food, fertilizer, and mineral deposits
- Easy cleaning — hose down or sweep; no re-sealing every season
Most residential patios are finished in a single day and ready for foot traffic within 24 hours.
Pool Deck Coatings
Pool decks have different demands: constant water contact, chlorine and salt exposure, and surfaces people walk on barefoot.
We apply textured polyaspartic and knockdown-style systems designed to lower surface temperature compared to bare gray concrete and dark pavers. The texture profile is adjustable — we can dial in more grip for steps and coping, less for lounging areas.
Consideration
| Our Approach |
|---|---|
Slip resistance
| Aggregate or knockdown texture rated for wet areas |
Heat
| Lighter colors and reflective finishes reduce heat retention |
Chemical exposure
| Topcoats resistant to chlorine, salt systems, and pool acids |
Cracking
| Crack chase and fill before coating; flexible base layers |
Existing cool decking that has chipped or delaminated can usually be resurfaced rather than torn out, which keeps the project shorter and less expensive than full concrete replacement.
Why Choose Our Epoxy Flooring Company in Scottsdale, AZ
Our crews follow a documented preparation and installation sequence on every job, and we use coating systems selected for Arizona's heat, UV exposure, and monsoon humidity. Below, we break down how the work happens and what goes into the floors we install.
What Does Our Professional Epoxy Flooring Process Involve?
We start with an on-site slab evaluation. That includes a moisture test, a check for existing sealers or old coatings, and measurements for accurate pricing.
Mechanical preparation comes next. We diamond grind the concrete to a CSP 2–3 profile, then repair cracks, spalls, and pitting with polyurea or epoxy patching compounds.
After vacuuming the surface, we apply the base coat and broadcast flake or metallic pigment while it's still wet. Excess flake is scraped and vacuumed the following day.
The final step is one or two clear polyaspartic topcoats. Most residential garages are finished in one to two days, with foot traffic allowed after roughly 24 hours and vehicle traffic after 72.
Which Materials, Products, Equipment and Related Services Are Used for Epoxy Flooring?
What We Use
Propane and electric planetary grinders with diamond tooling, HEPA dust extraction
What We Use
100% solids epoxy or moisture-tolerant primer
What We Use
UV-stable polyaspartic and polyurethane
What We Use
Vinyl flake blends, metallic pigments, quartz aggregate
What We Use
Polyurea joint filler, epoxy mortar
Anti-slip additives such as aluminum oxide or polymer grit are available for pool decks, patios, and entryways.
Related services we provide: garage floor coatings, patio and pool deck resurfacing, commercial and warehouse flooring, grind and seal, and removal of failed or peeling coatings.
Planning & Timeline
Most residential garage projects take one to two days on site, with the floor ready for foot traffic in 24 hours and vehicles in 72 hours. Below we outline how we schedule the work, inspect your slab, and help you choose a system that fits your space.
Epoxy Flooring Project Timeline – What to Expect at Each Stage
A standard two-car garage in Scottsdale follows a predictable schedule.
Stage | Typical Duration
|
|---|---|
Free on-site estimate
| 30–45 minutes |
Scheduling to install date
| 3–10 days |
Diamond grinding & crack repair
| 2–4 hours |
Base coat application
| 1–2 hours |
Flake broadcast (if selected)
| 1 hour |
Cure before scraping excess flake
| Overnight |
Polyaspartic topcoat
| 1–2 hours |
Light foot traffic
| 24 hours after topcoat |
Vehicle traffic
| 72 hours after topcoat |
Larger commercial spaces, patios with existing coatings, or floors needing extensive repair add a day or more. We confirm the exact schedule in writing before we begin.
Our Epoxy Flooring Process – Steps From Consultation to Final Completion
We follow the same sequence on every job:
- Consultation – We measure the space, discuss how the floor is used, and review color and finish options.
- Written quote – Square footage, system type, prep method, and cure times are itemized. No pricing changes unless the scope changes.
- Clear-out – You remove vehicles and belongings; we can advise on temporary storage for large items.
- Surface preparation – Mechanical diamond grinding to open the concrete profile, plus crack and pit repair with polyurea filler.
- Coating application – Base coat, decorative flake or metallic layer, then one or two protective topcoats.
- Walkthrough – We inspect edges, transitions, and coverage with you before we leave.
We keep dust contained with HEPA vacuum-attached grinders, which matters in occupied homes and retail spaces.
Assessing and Preparing Your Property for Epoxy Flooring – How the Evaluation Works
Every quote starts with an on-site slab evaluation, because concrete condition drives both cost and timeline.
We check for moisture using a plastic sheet test or calcium chloride reading, since vapor pressure from below is the most common cause of coating failure. We also look for existing sealers, oil saturation, spalling, control joint condition, and slope toward the garage door.
Older Scottsdale homes often have slabs with surface cracks or previous roll-on paint that must be ground off entirely.
If we find moisture above acceptable levels, we recommend a vapor barrier primer before the base coat. We'll tell you what we find and what it means for your quote rather than coating over a problem.
Epoxy Flooring Planning – Selecting the Right Materials, Design and Project Requirements
System choice depends on how the floor is used and how much UV exposure it gets.
- Full flake systems – Vinyl chips broadcast into the base coat. Hides minor slab imperfections and hides dust well.
- Metallic epoxy – Pigments moved during application create a marbled effect. Best suited to interiors and covered spaces.
- Solid color with polyaspartic topcoat – Clean, uniform look for showrooms and workshops.
- Quartz broadcast – Higher slip resistance for commercial kitchens and wet areas.
For Scottsdale patios and any floor receiving direct sun, we specify a UV-stable polyaspartic topcoat. Standard epoxy ambers over time under sunlight.
We also confirm slip rating, chemical exposure, and expected weight loads before finalizing the specification.
Cost & Budget
Epoxy flooring in Scottsdale typically runs between $4 and $12 per square foot installed, with most two-car garages landing in the $2,000 to $5,500 range. The final number depends on concrete condition, the coating system you select, and how much prep work the slab requires before we can start.
Epoxy Flooring Pricing Guide – What Affects Project Costs?
Three factors drive most of the variation in an epoxy quote.
Concrete condition comes first. Cracks, spalling, oil stains, and old coatings all require repair or removal before installation, and that labor adds to the total.
Surface preparation method matters just as much. Diamond grinding costs less than shot blasting, but shot blasting produces a deeper profile for thicker industrial systems.
System type and thickness round it out. A single-coat epoxy is far cheaper than a four-layer flake system with a polyaspartic topcoat.
Square footage also works in your favor — larger jobs lower the per-foot rate because mobilization and setup costs get spread across more area.
How Much Does Epoxy Flooring Cost? – Price Ranges for Different Options
Here's what Scottsdale homeowners generally pay:
Cost per Sq. Ft.
$3 – $5
400 Sq. Ft. Garage
$1,200 – $2,000
Cost per Sq. Ft.
$5 – $8
400 Sq. Ft. Garage
$2,000 – $3,200
Cost per Sq. Ft.
$7 – $10
400 Sq. Ft. Garage
$2,800 – $4,000
Cost per Sq. Ft.
$8 – $15
400 Sq. Ft. Garage
$3,200 – $6,000
Cost per Sq. Ft.
$9 – $16
400 Sq. Ft. Garage
$3,600 – $6,400
Labor accounts for roughly 40–60% of the total on most residential projects. Three-car garages, patios, and warehouse floors are quoted on-site since prep needs vary widely.
Comparing Epoxy Flooring Options – Cost Differences by Material, Method and Service Level
Epoxy vs. polyaspartic: Polyaspartic costs 30–50% more per square foot but cures in hours instead of days and holds up better under Arizona UV exposure. Straight epoxy can amber in sunlight; polyaspartic topcoats resist that.
Roll-on vs. broadcast systems: A rolled solid color is the budget option. Broadcasting flake or quartz adds material and labor but hides slab imperfections and improves slip resistance.
DIY kits vs. professional installation: Big-box kits run $200–$400 for a two-car garage. They typically apply at 3–5 mils thickness versus the 20–40 mils we install, and adhesion failures are common without mechanical grinding.
Service level: A one-day polyaspartic install carries a premium over a multi-day epoxy schedule.
Additional Epoxy Flooring Costs – Expenses to Consider Beyond the Base Price
Budget for these line items when they apply:
- Coating removal — $1.50 to $3 per sq. ft. for existing sealers, paint, or failed epoxy
- Crack and joint repair — $5 to $15 per linear foot with polyurea filler
- Moisture vapor barrier — $2 to $4 per sq. ft. when slab testing shows elevated moisture
- Concrete leveling or patching — quoted by severity on uneven slabs
- Anti-slip aggregate — $0.25 to $0.75 per sq. ft. for patios and entryways
- Cove base — $6 to $12 per linear foot, common in commercial kitchens
- Contents removal — some crews charge to clear a packed garage
We include a moisture test and slab inspection in every estimate, so these costs appear in writing before work begins.
Proudly Serving Other Areas
Our crews work throughout the Phoenix metro area, not just within Scottsdale city limits. If you live nearby, we can likely schedule an estimate for your garage, patio, or commercial space.
We also take projects in Peoria, Surprise, Queen Creek, Apache Junction, and Anthem.
Every job gets the same preparation process regardless of location. That means diamond grinding, crack and pit repair, and a coating system chosen for the way that specific slab will be used.
Traveling outside these areas? Give us a call. We consider projects beyond our standard service radius, particularly larger commercial jobs or multiple-unit installations.
Arizona conditions affect concrete the same way across the Valley — UV exposure, summer heat, and hot tire pickup. Our polyaspartic and epoxy systems are selected with those factors in mind, whether the floor sits in Scottsdale or forty minutes down the freeway.
Not sure if your address falls within our range? Reach out with your zip code and we'll confirm before scheduling anything.
Communities we regularly serve:
City | Common Projects
|
|---|---|
Paradise Valley
| Garage floors, patios, pool decks |
Phoenix
| Residential garages, warehouses, showrooms |
Tempe
| Rental properties, retail spaces |
Mesa
| Garage coatings, workshops |
Chandler
| Home garages, home gyms |
Gilbert
| Patios, garage systems |
Cave Creek
| Shop floors, detached garages |
Fountain Hills
| Garages, outdoor concrete |
Carefree
| Residential coatings |
Glendale | Commercial and residential floors |